Orbitco-CCNA-Pastquestions.com

Helping You Pass Your CCNA Exams
 

New ICDN 1 RIP v2 Lab Sim.

This is an Updated real Cisco ICND 1 exam question (Sept 2013). You might see a different IP addressing, VLAN configuration and Port allocation and Configurations.

As usual, take time to read through the question soas to clearly understand what Cisco want you to do.

Note: This Rip v2 Lab Sim is used for demonstration only; you might see different IP addressing and Port allocation in the real CCNA exam. But it all works the same way if you could just understand the technique.

I suggest you use packet tracer for practice.

 
 
 
Question:
 
orbitco-ccna-pastquestions.com 
 
 
Configure the router per the following requirements:
Name of the router is Apopka
Enable-secret password is cisco20
The password to access user EXEC mode using the console is RouterApass
The password to allow telnet access to the router is scan180
IPv4 addresses must be configured as follows:
Ethernet network 209.165.200.0/27 - router has second assignable host address in subnet.
Serial network is 192.0.1.128/28 - router has last assignable host address in the subnet. Interfaces should be enabled.
Routing protocol is RIP v2.

Instruction:
Central Florida Widgets recently installed a new router in their Apopka office. Complete the network installation by performing the initial router configurations and configuring RIPv2 routing using the router command line interface (CLI) on the Apopka router.

To configure the router (Apopka) click on the console host icon that is connected to a router by a serial console cable (shown in the diagram as a dashed black line).

Each of the windows can be minimized by clicking on the [-]. You can also reposition a window by dragging it by the title bar.

The "Tab" key and most commands that use the "Control" or "Esc" keys are not supported and are not necessary to complete this simulation. The help command does not display all commands of the help system.
 
 
Explanation
 
Use the following commands to configure the router:

1. Configure router or host name:

Router>enable
Router#configure terminal
Router(config)#hostname Apopka
Apopka#
 
2. Enable-secret password (cisco20):
Apopka#configure terminal
Apopka(config)#enable secret cisco20

 3. Set the console password to RouterApass:

Apopka(config)#line console 0
Apopka(config-line)#password RouterApass
Apopka(config-line)#login
Apopka(config-line)#exit

 4. Set the Telnet password to scan180:

Apopka(config)#linevty 0 4
Apopka(config-line)#password scan180
Apopka(config-line)#login
Apopka(config-line)#exit

 

5. Configure Ethernet interface (on the right) of router Apopka:

The subnet mask of the Ethernet network 209.165.200.0 is /27.

To save yourself time, as usual, create and follow the cram table:

Bit borrowed                       1        2     3      4       5       6      7      8

Bit value                       128     64    32    16      8       4       2      1

Subnet mask                128     192  224   240   248     252   254  255

Subnet prefix / CIDR    /25     /26    /27   /28    /29     /30

From the table above, /27 is the subnet prefix of mask 224. That means the bit value increment is 32

Therefore;
Network address: 209.165.200.0
Broadcast address: 209.165.200.31

Assignable host addresses = 209.165.200.1 - 209.165.200.30

The second assignable host address of this subnet is 209.165.200.2/27 

Use the following command to assign the second assignable host address to Fa0/0 interface of Apopka router:

Apopka(config)#interfaceFa0/0
Apopka(config-if)#ipaddress 209.165.200.2 255.255.255.224
Apopka(config-if)#no shutdown
Apopka(config-if)#exit

6. Configure Serial interface (left) of router Apopka:

Consult your table:

Serial0/0/0 IP 192.0.1.128/28:

From the table above, /28 is the subnet prefix of mask 240. That means the bit value increment is 16

Therefore;
Network address: 192.0.1.128
Broadcast address: 192.0.1.143

192.0.1.128 + 16 = 192.0.1.144

Assignable host addresses = 192.0.1.129 - 192.0.1.142

The last assignable host address of this subnet is 192.0.1.142 

Use the following commands to assign the last assignable host address to interface s0/0/0 of Apopka router:

Apopka(config)#interface S0/0/0 (depending on the interface number)
Apopka(config-if)#ip address 192.0.1.142 255.255.255.240
Apopka(config-if)#no shutdown
Apopka(config-if)#exit

7. Configure RIP v2 routing protocol:

Apopka(config)#router rip
Apopka(config-router)#version 2
Apopka(config-router)#network 209.165.200.0
Apopka(config-router)#network 192.0.1.0
Apopka(config-router)#end

Save the configuration:

Apopka#copy running-config startup-config (don’t forget this bit)

Finally, don’t forget to use the ping command to verify your configuration and connectivity!

 
 
 


 
 
 
 
Sign Up For Post Updates

* required


*



Email Marketing by VerticalResponse

 
 
 

 PrivacyPolicy  Contact Us  Advertise

Copyright  2012. Orbitco-Computer-Solutions.Com. All rights reserved.  

The information provided on this website is for informational purposes only.
orbitco-ccna-pastquestions.com makes no warranties, either expressed or implied, with respect to any information contained on this website.

orbitco-ccna-pastquestions.com reserves the right to change this policy at anytime without prior notice.
Cisco
and All related product mentioned in any portion of this website are the registered trademarks of Cisco.com 

and their respective owners